Tool Care
This page features topics and my opinions on care and use of your leather tools.
Surfaces For Punching
Before I get into surfaces, there are few other factors that can affect punching. First off is good support. There needs to be solid support underneath the punching area to minimize bounce and absorption of the force of the punch penetrating the leather. Some people punch over the leg of work bench rather than the middle. Other supporting surfaces can be something like a stump or section of tree trunk. You can also use something with some mass to help prevent bounce. Large anvils or metal plates work well as a surface support. I use a granite inspection plate on one bench that does have some flex and the mass of the granite helps to negate the flex and bounce.
The second factor is the weight of the striking tool. It is the length of the cutting edge of the punch that determines how much force will be needed to punch through. Obviously a 1 inch round punch will require more force than a 1/8 inch round punch. Complexity of the punch factors in after that. A 1-1/2 inch round punch has about 4.7 inches of length. Each scallop on a 1-1/2” rosette or concho punch adds more length and the total length of edge increases by about 40% more than the comparable round punch. Obviously the more length of a punch edge, then a heavier striking tool or more force will be required to punch.
Finally - Surfaces. I want my punches to cut cleanly and completely through the leather and lightly penetrate the punching surface. That gives me a complete cut all the way around and no sections of uncut leather that pull and feather. The three major materials I recommend are plastic, shoe sole material, and heavy scrap leather. For plastic I prefer low-density polyethylene (LDPE). This material is available at most plastic and commercial kitchen suppliers. A large share of the cutting boards sold at department stores are LDPE also. The low-density polyethylene boards will allow penetration of the punch edge without being hard enough to damage the edge. The shoe sole material I prefer is the black type sold in sheets. Some leather suppliers sell it small sections and call it “poundo board”. You can order it from many shoe repair suppliers as well. Personally, I buy it in 18x36 sheets that are 5/16 inch thick. It is relatively inexpensive as well. The final surface I like is a piece of heavy scrap leather. This allows a nice clean punch for smaller punches and it is easy to pull the punch from the material.
My particular choice of material depends on what I am cutting. The poly boards are a bit slick and tend to slide around more. That said, they are my choice for most small round punches, strap end punches, and small to medium bag punches. The sole material is grippy and stays in place. I like it for all my larger punches and especially rosette punches. Smaller punches tend to stick in sole material more than larger punches so that is a consideration. For finer punches like very small round punches and especially lacing chisels, I prefer scrap leather. The scrap leather is a very forgiving surface and in my experience punches pull out easier.
Cutting Surfaces for Knives and Blades
In this post I am going to share my personal favorite surfaces for cutting. Some of these recommendations will depend on the available bench and table space in your work area.
For cutting with round knives and fixed blade knives I want a durable and smooth surface that will not allow a blade to penetrate deeply. I want the blade edges to glide over the surface, not dig in. Part of this depends on the user and you will find with experience that downward pressure is not necessary for clean cuts with most leather and a sharp blade. Think “forward not down”. My favorite surfaces for cutting are plastics – either high density polyethylene(HDPE) or ultra high molecular weight polyethylenbe (UHMWPE). Some prefer acetal/Delrin but that material is generally more expensive with little difference. These plastics are hard enough that they don’t allow a blade to penetrate deeply yet forgiving enough to not damage an edge. They can be occasionally renewed by sanding if they get deeper grooves. I prefer the largest piece I can to cover a dedicated cutting bench. I don’t want to use a smaller piece under a side of leather and accidentally run off the cutting board underneath. You may not have that luxury in your workspace but consider the biggest piece you can work with. These cutting boards can be found at many plastics supply shops, commercial kitchen and food handling suppliers, and some home improvement supply stores. This material is brittle and not what I recommend for punching however. I will cover punching surface preferences in another post.
Another surface material that seems to attract a lot of mention are the self-healing cutting mats. I do not like them for most knife cutting at all. The blades easily penetrate the surface and then drag, drag, drag. I find they dull fixed blade tips quickly as well. I was never without one in my shop though. I think they are excellent for the rotary blade/roller blade knives. They allow clean cuts and the rolling action of the blade tends to neutralize the drag. For best results think roll forward, not push down.
The final surface for me is a piece of tempered glass and again - a nice size piece. I was taught to edge skive on glass. The glass allows the tip of the blade to glide over that smooth surface without digging in and dragging like you get with a cutting board. Some people skive on marble or granite stamping surfaces but that can be wearing on the blade. A good sharp knife and you can push away on most leathers and get an even skive in one pass with glass. Using the Skife razor blade skivers also will let the blade glide if you are cutting further up the curve. I have an old flat side window from a car. I have seen some people use a curved glass surface also. This lets the leather lay around the curve and the blade angle can be lower with less interference with the leather holding hand. I have seen people use gallon glass jars or turned over bowls for this and do some paper-thin edges for inlays.